Translated points and Rabinowitz Floer homology

We prove that if a contact manifold admits an exact filling then every local contactomorphism isotopic to the identity admits a translated point in the interior of its support, in the sense of Sandon [San11b]. In addition we prove that if the Rabinowitz Floer homology of the filling is non-zero then every contactomorphism isotopic to the identity admits a translated point, and if the Rabinowitz Floer homology of the filling is infinite dimensional then every contactmorphism isotopic to the identity has either infinitely many translated points, or a translated point on a closed leaf. Moreover if the contact manifold has dimension greater than or equal to 3, the latter option generically doesn't happen. Finally, we prove that a generic contactomorphism on $\mathbb{R}^{2n+1}$ has infinitely many geometrically distinct iterated translated points all of which lie in the interior of its support.Comment: 13 pages, v2: numerous corrections, results unchange

Comparison of predicted and measured low-speed performance of two 51 centimeter-diameter inlets at incidence angle

Theoretical and experimental internal flow characteristics of two 51-cm-diameter inlets are compared. Theoretical flow characteristics along the inlet surface were obtained from an axisymmetric potential flow and boundary layer analysis. The experimental data were obtained from low-speed tests of a high-bypass-ratio turbofan engine simulator. Comparisons between calculated internal surface pressure distributions and experimental data are presented for a free-system velocity of 45 m/sec and for incidence angles from 0 deg to 50 deg. Analysis of boundary layer separation on the inlet lip at incidence angle is the major emphasis of this report. Theoretical boundary layer shape factors, skin friction coefficients, and velocity profiles in the boundary layer are presented, along with the location of the transition region. Theoretical and experimental separation locations are also discussed

Status of the NASA YF-12 Propulsion Research Program

The YF-12 research program was initiated to establish a technology base for the design of an efficient propulsion system for supersonic cruise aircraft. The major technology areas under investigation in this program are inlet design analysis, propulsion system steady-state performance, propulsion system dynamic performance, inlet and engine control systems, and airframe/propulsion system interactions. The objectives, technical approach, and status of the YF-12 propulsion program are discussed. Also discussed are the results obtained to date by the NASA Ames, Lewis, and Dryden research centers. The expected technical results and proposed future programs are also given. Propulsion system configurations are shown

Computer program for calculating laminar, transitional, and turbulent boundary layers for a compressible axisymmetric flow

Finite-difference computer program calculates viscous compressible boundary layer flow over either planar or axisymmetric surfaces. Flow may be initially laminar and progress through transitional zone to fully turbulent flow, or it may remain laminar, depending on imposed boundary conditions, laws of viscosity, and numerical solution of momentum and energy equations

V/STOL aircraft configurations and opportunities in the Pacific Basin

Advanced aircraft configurations offer new transportation options for the Pacific Basin. Described is a range of vehicles from low-disk to high-disk loading aircraft, including high-speed rotorcraft, subsonic vertical and short takeoff and landing (V/STOL) aircraft, and subsonic short takeoff and landing (STOL) aircraft. The status and advantages of the various configurations are described. Some of these show promise for satisfying many of the transportation requirements of the Pacific Basin; as such, they could revolutionize short-haul transportation in that region

Application of boundary integral equations to elastoplastic problems

The application of boundary integral equations to elastoplastic problems is reviewed. Details of the analysis as applied to torsion problems and to plane problems is discussed. Results are presented for the elastoplastic torsion of a square cross section bar and for the plane problem of notched beams. A comparison of different formulations as well as comparisons with experimental results are presented

Civil applications of high-speed rotorcraft and powered-lift aircraft configurations

Advanced subsonic vertical and short takeoff and landing (V/STOL) aircraft configurations offer new transportation options for civil applications. Described is a range of vehicles from low-disk to high-disk loading aircraft, including high-speed rotorcraft, V/STOL aircraft, and short takeoff and landing (STOL) aircraft. The status and advantages of the various configurations are described. Some of these show promise for relieving congestion in high population-density regions and providing transportation opportunities for low population-density regions

Aircraft technology opportunities for the 21st Century

New aircraft technologies are presented that have the potential to expand the air transportation system and reduce congestion through new operating capabilities, and at the same time provide greater levels of safety and environmental compatibility. Both current and planned civil aeronautics technology at the NASA Ames, Lewis, and Langley Research Centers are addressed. The complete spectrum of current aircraft and new vehicle concepts is considered including rotorcraft (helicopters and tiltrotors), vertical and short takeoff and landing (V/STOL) and short takeoff and landing (STOL) aircraft, subsonic transports, high speed transports, and hypersonic/transatmospheric vehicles. New technologies for current aircraft will improve efficiency, affordability, safety, and environmental compatibility. Research and technology promises to enable development of new vehicles that will revolutionize or greatly change the transportation system. These vehicles will provide new capabilities which will lead to enormous market opportunities and economic growth, as well as improve the competitive position of the U.S. aerospace industry

Boundary-layer analysis of subsonic inlet diffuser geometries for engines nacelles

Theoretical Mach number distributions and boundary-layer parameters are presented for subsonic nacelle inlet diffuser geometries with length to exit diameter ratios ranging from 0.4 to 1.6 and diffuser exit area to throat area ratios ranging from 1.1 to 2.0. The major portion of the study was done with a cubic diffuser contour with the inflection point at the midpoint of the diffuser, a diffuser throat Mach number of 0.6, and a free-stream Mach number of 0.12. Calculations were performed at both model (diffuser exit diameter, 30.5 cm) and full-scale (diffuser exit diameter, 183 cm) sizes. Separation limits were defined by establishing a separation boundary on plots of diffuser area ratio as a function of diffuser length to diameter ratio. The effects of diffuser contour, inlet lip geometry, and throat Mach number on the boundary-layer characteristics are illustrated. The major results of the study indicate that the separation boundary is shifted to greater area ratios by (1) increasing the diffuser length, (2) increasing the scale of the diffuser and, (3) moving the inflection point of the diffuser contour to or ahead of the midpoint of the diffuser